In this video I'll tell you about making the front view of a Ballister.
And these are really shapes which you commonly see on the Boucher's or on the stairs on the side of
your stairs.
So I'll start this Pallister with the rectangle tool.
So let's go to this rectangle tool and the draw panel now click anywhere in the drawing area to start
the rectangle and then type at the end of this rectangle is 6.
And the word is to and press enter.
So there we have it.
So this is the first rectangle that we have now taking the reference of this rectangle.
I'll make a line so line to click on this point the midpoint on the bottom side of this rectangle.
And now I'll make a line with per unit so you don't need to be very precise but this length you can
make it all of you in short length of shorter length if you want.
But in this case I'm just using an approximate distance of 30 unit for this line.
This will act as a reference only.
Now let's go to rectangle again and click somewhere here.
And again I'll make another rectangle.
But this time with the length of five and a height of one and press enter.
So there we have it.
So the second rectangle.
Now let's selected and exploded.
So now I'll type X and press enter so that exploded.
And now we can remove these two lines.
These two are no longer needed and we'll add the rounded edges here rounded corners.
So I'll go to fellate and I'll click on the side and the side press enter again to repeat the filleted
and this one and this one.
And there we have it.
So that's the required shape which we needed.
I selected all select move.
Click on this point the midpoint of the bottom and move it on this midpoint right there.
All right.
Now we'll make another one of this so we'll make another copy of this shape.
And for that once again I'll go to rectangle click anywhere to start that and then type at.
Now in this case the length will be four.
And the word will be point eight.
And press enter and repeat the process.
So select it type x press enter that will explode it.
Well let's just zoom in a little bit.
It's get rid of these two lines and go to fellate and add the fillets here.
You can select any radius and in this case since the lines are parallel it will add the semicircular
shape.
Now we need to move properly on the right spot for that or just selected.
Good move.
Select this point and just move to.
Now we need to move upwards so select selected again carefully make the selection so that only the parts
of the the first geometry selected.
Not this one look at this in this case.
I accidentally selected this line so press and hold shift and click on it again to de-selected.
Now that is removed from the selection set.
Now we can move it up forwards.
Now the distance between this part and this part is 3.1 0.
So I'll go to move on any point pick up votes and add the distance 3.1 0 press enter.
So there we have it.
Now we'll add the arc shape and for that I'll select start and radius.
So I go to arc and select the start and radius also at this point as a starting point the intersection
point then this point.
And the second point.
And in this case the radius is 1.6 and Precentor and there we have it.
So that's the shape which we needed.
So we can now repeat the Prosser's on this side but make sure that you select the proper order of.
Because in this case if I would have selected this and point first and then the second then would be
formed right in this direction not in this direction.
So make sure that you select the first and the second point properly in a proper order.
So in this case I also like mirrors on this arc.
Press Enter now click on any of these two points and the axis.
There we have it.
That's the mirror image.
All right.
Now let's move ahead.
And now I'll make a reference line so line click on this and point and then at a distance of two point
three and press enter.
So here we have this reference language has been added.
Now using the reference of this line I'll make another circle.
So I go to circle select the center radius go to this end point and now add a circle with a radius of
three.
And press enter.
OK.
Now let's zoom out a little bit and let's make a copy of this shape so we've already made this shape.
We need to make a copy of this was selected completely.
Only this one and go to the anywhere and that will copy this geometry.
Now move it upwards.
And the distance in this case should be 12.
So let's type 12 and press enter.
So right now you can clearly see that the gap between this one this geometry and this geometry is eleven
point two.
But since we need to select the corresponding point we need to add the gap on this which is pointed
toward the total gap will be 12.
In this case and so this is between the stop point at this point or any corresponding points.
So we have this shape.
Now let's go to circle to and select tangent engine radius.
Now click here somewhere close to this point on the circle.
Then click on flet and now add a radius of 6.
And press enter and that will add this tangent circle.
Now we'll trim some of the geometries which are no longer required and for that and go to trim presenter's
Ultram this part Altro and this part and this part.
So these are the geometries which are no longer needed.
I'll select this one and Halliday's it.
Now Elssler both of these and I'll make a mirror image.
So the mirror select this point and this point and there we have it the mirror image.
All right.
Now let's move ahead.
So now we need to add some lines and set that line to an instead of rectangle.
We approach this part of the drawing in a different way.
So now at this point and move to the right and at a distance of 1.5 and press Enter NOW and move in
the opposite direction and at a distance of 2.3 and presenter.
Presenter again to exit this command and remove this now we can make a mirror image of this as selected
go to mirror and make a mirror image.
So this is another way of making this kind of shape you could have selected the rectangle tool as well.
But obviously this is another workflow that you can use.
Now moving on to the next part let's go to rectangle tune.
And in this case once again Helmick the rectangle Savill here and type at the left of this rectangle
is obviously 3 and the height is obviously point 6.
And press enter.
So there we have it.
So once again Alex plaudit to select an X and enter now we can get rid of these lines.
I'll go to Follette and these two lines press enter again to repeat it and select these two lines and
there we have it.
Now let's Sylhet them bought and now we need to move properly so as select move to select this midpoint
and just make sure you track this point and click right where it is needed.
So there we have it.
Now we need to add the last rectangle so good or rectangle to click anywhere to start that one then
type at.
In this case the length of the rectangle is four point four zero and the height is one.
And press Enter once again select it go to move click on this midpoint move into.
We only need to add this Fielitz or go to fill left and the Fielitz radius is point 3.
So let's go to radius and let's type point 3.
Press Enter select multiple because we want to repeat it and apply it here as well as here.
And that completes we're trying.
Now you can remove this line it's no longer needed.
And we also have this extra construction line.
There we go.
So that's the baluster shape which we needed.