In this review I will tell you about the Lenten and reverse tools of to.
So here we have these three simple geometries.
And we start with the Lenten tool here so you can use Atlantan tool to find out the length of different
objects in the drawing and you can also use it to increase the existing length of the objects for example
here we have a line and an out.
Now using the lengthened tool we can increase their length and hero so we can increase the length of
this are called the circumference of this arc.
So that will affect the included angle.
So to start to expand them would you panel and select the length and tool from here not selected and
click on the object whose length you want to find.
So in this case I'll click on this line and here we have the land line which is 100 in it.
Now let's assume that we want to find the length or the circumstance of this arc.
So click on it and we have the circumference of the arc along with the right angle.
So in this way you can use this tool to find the length of different geometries.
Now using this tool you can also increase its length.
So as you know the length of this line is 100 unique as shown here.
Let's say that we want to change its length 220 units for data.
I will select this option first.
Now using Delta option you can change the lend to any value.
So here we want to change its length by 20 units of type 20.
Press enter.
Now click on the side on which you want to increase the line so I'll click close to this end point and
the lint will increase by 20 units towards the right side.
You can now also click on this leftside increase it by 20 units here and you can keep on clicking if
you want to increase length even further.
Now let's press enter to exit this command.
Now I'll presenta again to repeat the command.
And now once again I'll change the length of this arc.
So in the previous case we have changed the length of this line I will change the length of this arc
but in this case instead of using the Delta option as I like the present option.
So let's select this potent option.
Now using the percent option you can also change the length of existing objects and for that you can
enter a value which is greater than 100 and also less than hundred.
So if you throw a value which is less than for example a D that would decrease the length and it will
decrease by 20 percent.
And if you enter a value like hundred twenty percent it will increase the length of the existing object
by 20 percent.
So obviously entering a value 100 percent will not make any change.
So in this case enter a value of 70 percent and now press enter.
Now click on the site a follow up from where you want to decrease the length.
And here we want to decrease it so you can see that the length will be reduced.
So let's click and the length has been reduced to 70 percent off its original value.
Again press enter to exit this command.
Now you can also press enter to repeat it.
And now we have a total lenth option here.
So let's look at the store.
And now you can enter a totally lende for the objects in this case.
We know that the length of this line is now 140 and it's because we have increased the length by Duranty
units to our right and left side.
Now let's see that we want to decrease its length and we want to make it equal to 60 units so I'll type
60 as the total length.
Press enter and now on the site from there you want to please if you click on the right side the left
will protect these from the side if you click on the left side the lens will decrease from that this
left side and now here we have the line with a length of 60 and you can also check it using the lenth
in common.
So again press enter and click on this line.
And here we have this 60 unit.
And if you want to change the length of this line now or the length of this are dynamically by using
your cursor then you can select this dynamic option and now you can click on the line and you can move
your cursor to change the value.
Similarly you can also click here and change the length of this arc just like this.
So now let's.
It is both of these and geometries So now let's have a look at the reverse too.
So using the tool you can reverse the direction and also orientation of the object.
So here we have a party line and this polyline we have this starting with zero unit and an ending with
of 10 unit.
Now it say that we want to reverse its direction.
For that we need to expand the panel and select variabilis tool so selected.
Now select the object and press enter.
Now although you may not see the change in direction but when you look on the command line.
Just let's expand it.
You'll see that the object direction has been reversed.
So obviously the object that action has been reversed but we are not able to see any change yet in this
polyline because it has not traversed the order in which the Boyland has been made and in order to apply
the change on the order of this polyline you need to change the lines of what system variable to one.
So let's type the line reverse words and press enter.
So now you can see that it's the default value set to zero.
Let's change it to 1 and present it.
Now I will repeat the command.
So let's go to this mortify select reverse tool.
Select the polyline and press enter.
And now the direction has been reversed and also the orientation has been reversed.
In this case this reverse direction 2 is especially helpful for this kind of cases and it's also helpful
in the situations where you have a line type containing text and when the direction of text is not appropriate
or not according to your requirements you can use this tool to reverse the direction off line or reverse
the direction of line type to make it appropriate as per your requirement.
So let's now once again change the system variable back to zero and lets it is this object as well.
So this was all about Lenton and reverse tool of Autocad.